News
Tracking information, focusing on news
Do you know how to replace your own wiper blades?
2022-12-12
The wiper blades on our cars need to be replaced every year, and I believe that many people have not been paying much attention to this piece. Now you need to know that if the wiper rubber strip is used for a year, then you need to return a new one. The following for you to say how to replace the method, want to know if you hurry up to learn it, I hope it can bring you help.
We in the replacement of wiper tape there are some knowledge points are needed to know, for example, but many friends to replace the old wiper tape found that, in addition to the aging of the tape elsewhere are quite good, can not just change the tape ah? This is actually possible. In our replacement you also need to know is actually wiper tape it first is not universal, different car wiper tape size is not the same, it is the left and right two tape length is also different. So this is something you need to be clear about, later in the choice is when you have to buy according to their own needs and the actual situation. Before you buy and the shop ask clearly, the price is usually a few dollars a piece. In exchange for a towel wrapped wiper, the purpose of doing so is still in order to prevent smashed windshield first change the boneless wiper, some wipers are straight into the interface, hold down the switch to pump up, you can take the wiper. Here also need to know you must be wrapped in a towel, support, and then put back. The reason for this is definitely still to avoid wiper tape change when touching or smashing the front windscreen in front. If you still do not understand if you can learn, I believe that for most people will still be used.
In addition, for friends in the replacement of wiper tape when the next job is to take the pliers to the middle of the pressure, towel wrapped to take down the wiper tape, and then a hand break can be removed on both sides of the left and right side of the small buckle, the next to take the middle of the large buckle, this time wiper tape in the middle of the two pieces of steel clamped, take the pliers to the middle of the steel piece of the pressure can produce a certain deformation, you only need to do so! You only need to do this to take it down, and here you have to pay attention to is in the clip remember to use a towel to wrap the wiper tape, to avoid damage to the paint on the steel plate. Then the big buckle off after the replacement of the new wiper tape, pay attention to the left and right of some cars is not the same length, then you must not take the wrong. And also need to pay attention to is the more don't install the opposite, the steel blade aligned with the guide groove at both ends of the bayonet is upward a slant, this is the wiper flow design. And it's the rubber strip installed do not get reversed, otherwise it is certainly not stuffed, the next thing you have to do is to the rubber strip stuck in the middle of the steel blade to push the two sides of the bayonet can be. Here to note that the side it is going to have the upper and lower two guide grooves, the installation of the steel sheet to align the upper guide groove, or also can not be installed. As long as you master these methods you can change it yourself.
Previous page
Next page
Previous page
Next page
07-19
China auto parts industry market status and development trend analysis
Auto parts industry as the foundation of the development of the automotive industry, to help China's independent automotive industry bigger, stronger and better solid support. 60 years, China's auto parts industry continues to grow
07-19
As a professional automotive materials and design, process and equipment, quality and assembly, engineering and service technology industry event, it presents system integration solutions in the field of automotive engineering from an international perspective, and promotes the development of international automotive manufacturing equipment technology exchange and trade!
07-19
How to increase the excellence of auto parts machining?
First, to choose to engage in machining work technology good staff. There is no excessive technology, difficult to do a good job of machining, we all know that mechanical parts processing is not tolerate shoddy. In the process is also difficult, even if you can do a good job, can spend a lot of time, if the beginning did not start a good head, it will be easy to lose the effort, the effectiveness of the loss is not worth it.
07-19
How to improve the machining efficiency of automotive parts processing
Parts processing plant to provide parts processing, need to take into account the appropriate technology as well as details and processing efficiency, then parts processing plant how the product processing efficiency? Here we will look at the following introduction.
Add: No.206, Lubei Road, Yuhuan Economic Development Zone, Yuhuan City, Taizhou City, Zhejiang Province, China.
Mobile phone: 0576-87227223 / 13906760270
E-mail: mksalesdep@cnmkjx.com
Copyright © Taizhou Meike Machinery Co.Ltd. All Rights Reserved Powered by www.300.cn SEO Business license
